Troubleshooting the Vampire 500 V2+

Before continuing, please consider the following:
  • My storage device does not boot when connected to the IDE port of the Vampire.
    • Try booting with no Startup-Sequence. If it works, then try disabling commands in your S:Startup-Sequence to isolate the command that is causing the problem.
    • Your storage device might be bad / damaged. Try a different one.
    • The adapters and cables between the board and your storage device might be loose. Make sure to tighten them.
    • The adapters and cables between the board and your storage device might be bad / damaged. Try different ones.
    • The storage device might have been prepared incorrectly. Try booting from it on a different Amiga (or on an Amiga emulator) to make sure it is set up correctly.
    • Try formatting the storage device and preparing it from scratch.
  • My storage device takes an unusually long time before starting to boot, when connected to the IDE port of the Vampire.
    • The adapters and cables between the board and your storage device might be bad / damaged. Try different ones.
  • I am getting read/write errors on my storage device connected to the IDE port of the Vampire.
    • Your storage device might be bad / damaged. Try a different one.
    • The adapters and cables between the board and your storage device might be bad / damaged. Try different ones.
    • The storage device might have been prepared incorrectly. Try using it on a different Amiga (or on an Amiga emulator) to make sure it is set up correctly.
    • Try formatting the storage device and preparing it from scratch.
    • The cables between the board and your storage device might be too long. Try shorter ones.
    • You might have set “Fast IDE” to a speed level that is too much for your configuration, especially if your connection cables are too long. Update your VControl IDESPEED command to set a lower speed level.
2020/02/13 03:28
  • I am getting read/write errors on my SD card inserted into the MicroSD slot of the Vampire.
    • Your SD card might be bad / damaged. Try a different one.
    • The adapters and cables between the MicroSD slot and your SD card might be bad / damaged. Try different ones.
    • The SD card might have been prepared incorrectly. Try using it on a different Amiga (or on an Amiga emulator) to make sure it is set up correctly.
    • Try formatting the SD card and preparing it from scratch.
    • If you have an extension cable, it might be too long. Try a shorter one.
    • The MicroSD speed might have been set to a level that is too much for your configuration, especially if your extension cable is too long. Use the VControl SDSPEED command to set a lower speed level.
2020/02/13 03:31
  • I did a power-cycle, but it seems ineffective.
    • Please wait at least 10 seconds after powering off.
    • In addition to turning off the power to the Amiga / Vampire, disconnect all devices that have their own power connection, such as Digital Video, Ethernet and USB-Blaster cables, to prevent power backfeed into the Vampire.
2020/04/04 13:15
  • My monitor / TV does not show the Digital Video output of the Vampire.
    • Your Digital Video cable might be bad / damaged. Try a different one.
    • Try a different monitor / TV.
    • Try entering the Amiga Early Startup Control, by holding down both mouse buttons during power-on. This screen will be output from the legacy video outputs of the Amiga, so you should see it on a monitor connected to one of those ports, assuming that this monitor was working fine without the Vampire. If you can't see anything at this point, then please refer to the other solutions for stability problems.
    • If you can see the Amiga Early Startup Control, boot your Amiga without RTG, by following the instructions under “Disabling RTG” on this page. The resulting screen will be output from the legacy video outputs of the Amiga, so you should see it on a monitor connected to one of those ports. If you can't see anything at this point, then maybe your storage device does not boot properly. Please refer to the other solutions for boot problems.
2020/02/13 03:37
  • I am getting an unstable Digital Video signal (noise / snow / stripes / black screen / flashing screen) when using high resolutions on my monitor / TV.
    • Some early Vampire 500 V2+ boards (with Rev: 2) could have this problem. Solutions:
      • Try using a “Digital Video repeater/amplifier” like this one.
      • Try a higher-quality, shorter Digital Video cable.
  • My Vampire 500 V2+ is having stability issues.
    • Your PSU might be bad / damaged. Try a more powerful, higher-quality PSU.
    • Remove add-ons that consume too much power.
    • Make sure that the Vampire is tightly connected to the CPU socket, and that the connection contacts are clean.

You are here: start » vampire » v500-v2plus » troubleshooting

Last modified: le 2020/04/04 13:18